It may sound similar to a daunting task to replace a broken fence post but it is and not as difficult as it can certainly seem. It will have a chunk of hard work and some simple tools you most likely already have got within the shed or garage. Where can you start? On the web that have got to evaluate the project plus the damage. Did the post rot in support of break or maybe it was sheered off due to some nasty weather. Perhaps there is still a remaining stump or perhaps it broken off from the ground or concrete level? Do not be afraid, the project is moderately difficult and must just take about 1 or 2 hours of their time to perform and then your fence will likely be terrific once again.
Difficulty Level: Moderate
Time Required: Approximately One or two Hours
- Pry Bar
- 1 Replacement Post – Typically 4″ x 4″ x 8′ Cedar or Treated Lumber
- 1 – 80 Pound Bag of Quickrete Concrete Mix
- 3″ Wood Screws (Approximately 12 Screws)
- Auger or Clam Shell Post Hole Digger
- Bag of Gravel
- Hand Saw or Circular Saw
Typically, most fence posts are set inside the ground using concrete but others are installed using packed dirt on the fence post hole. Understand what see concrete around the walk out, take an average shovel and dig down a small number of inches towards the broken post location to see in the event you hit concrete. Most fence posts are placed in concrete and also for the most part the standard post hole is roughly eight (8″) to 12 (12″) inches across and the majority are about twenty-four (24″) inches deep.
One can find different ways of thinking relating to removing providing post. A lot of people choose to smash and grab technique which is certainly simply utilizing a hammer and chisel or pry bar to the concrete into small pieces and pull them right out of the existing hole 1 by 1. The tactic really does work but is much work might take between one (1) and two (2) hours of employment to extract the concrete with the hole. It really is fine should you have one particular post to exchange in case there are actually multiple, the repair involved may be very tedious and tiring its keep be more effective ways.
The process I enjoy could be to require a long, skinny bladed shovel and find out the dirt simply to one side on the concrete exposing the side with the concrete block. Just be sure you pile the dirt close to the hole being the dirt you remove will likely be would once re-pack the hole as soon as the post and concrete block is taken off within the ground. Out of the aspect the concrete, dig out about six (6″) to eight (8″) inches and down twenty-four (24″) inches. This allows for any pocket as wide because concrete block. If your piece or stump from the existing post is set up, technology-not only and begin moving the concrete block between the two together with the new pocket space you just created. Once it happens to be loose, you need to be able to use your shovel or pry bar as a lever and lift the concrete block on the hole. Take care guarantee you lift along with your legs given that the concrete block can weigh just as much as eighty (80) pounds. Generally if the existing post or post stump has stopped being coupled to the concrete, just be able to use a pry bar as well as your shovel to maneuver the actual concrete block back and forth similarly loosening it from the original placement. Once, the block is movable, make use of the same process as outlined above but be careful to employ proper lifting techniques when treatment of concrete. A doctors visit is not prescribed on this project.
After the block is removed, use the dirt you far from the excavation to complete the six (6″) to eight (8″) inches you originally dug out. Ensure that you pack the dirt solidly simply because it will supply the lateral support for that new post if it is available. The concrete you employ when you set the newest post provides loads of support as well as attaching the present fence structure although the better you pack the dirt, the better the end result. Just be still a normal hole approximately twenty-four (24″) inches deep and approximately eight (8″) to 12 (12″) inches wide.
From here, you might want to bring your clam digger or post hole digger or you do not need one, only use your shovel and find out approximately two (2″) inches towards the bottom within the hole. Then add loose gravel in these two (2″) inches for drainage to maintain water from your bottom of the post. Understand what have or wouldn’t order a bag of gravel when you purchased your replacement post and concrete, don’t be concerned. The concrete has gravel inside and often will work nonetheless the gravel does make your drainage far better. After you’ve the base ready, it is time to install the replacement post.
Grab your replacement post and center it on the hole. For those who have a helper, keep these things hold the post assure which it lines up correctly with the fence and then the old post you removed. Upon getting it inside correct position, open an eighty (80) pound bag of Quickrete concrete and pour it dry into the hole. Remember to be wearing eye protection so to cover orally so that you tend not to inhale the concrete dust that typically spews out of your hole because you pour in the mixture. Pour the entire contents on the hole. Grab a garden hose or just a bucket of water and start pouring water towards the hole and make certain to pour around the new post at a circular pattern in order to receive the whole top layer of your concrete wet. The tank are going to bubble the way it starts seeping into the bottom. Will continue to add water until it pools slightly. It should absorb through the mix. At this moment, bring your pry bar or a section of rebar and even a sturdy stick and get started poking the concrete mixture to support receive the water to circulate to the end plus take out the air bubbles that form. It’s OK if your water pools just a little along with improve mixture too wet simply because it is going to take longer to get.
Now bring your level and assure the post continues to be to use upright vertical position. It is actually helpful when you verify multiple sides assure the bubble within the level is inside the middle and regarding the marks. Once the post is level, use pieces of wood to establish a stand of sorts at the end to hold the post from moving as the concrete sets up overnight. The concrete commences setting and according to the climate must be ready the next day to re-hang fences pieces. If for example the post moves, wiggle it on the vertical position and be able to along with your stick or pry bar, move the concrete mix around consequently it touches the post on all sides in the earth without having gaps. If gaps form, you need to add a slice of additional water to help make the mixture more liquid. Any pooled water will probably be made available to the concrete and surrounding dirt and in addition evaporate for the reason that concrete sets.
Down the road, you should be ready to re-affix the fence to your post also it need to be terrific once again. Before you attach the actual fence pieces, you can even examine the height within the fence post as opposed to other posts with your fence line. Depending on the the majority of your fence, you really should begin using a hand or electric saw to take the new post to complement other posts for your fence. When the post doesn’t have to be cut, you’ll then attach the existing fence pieces in the new post. Be sure to use screws as you attach a gate it back into the new post to guarantee a much more stable connection than nails which could grab in windy or rainwater conditions after some time causing integrity issues.
The entire project is a moderate or medium difficulty project and may take approximately sixty (60) to ninety (90) minutes to finish.