It may sound like a daunting task to replace a broken fence post yet it’s and not as difficult as it may seem. It is doing relax and take a little bit of elbow grease and some simple tools you most likely curently have within the shed or garage. Where do you really start? On the web that have got to measure the project and also damage. Did the post rot and break or maybe it was sheered off caused by some nasty weather. Will there be still a remaining stump is actually it broken off for the ground or concrete level? Do not let yourself afraid, the project is moderately difficult and must only take about 1-2 hours of your time in order to complete and also your fence could be terrific once again.
Difficulty Level: Moderate
Time Required: Approximately One to two Hours
- Pry Bar
- 1 Replacement Post – Typically 4″ x 4″ x 8′ Cedar or Treated Lumber
- 1 – 80 Pound Bag of Quickrete Concrete Mix
- 3″ Wood Screws (Approximately 12 Screws)
- Auger or Clam Shell Post Hole Digger
- Bag of Gravel
- Hand Saw or Circular Saw
Typically, most fence posts are positioned into the ground using concrete but other people are installed using packed dirt within the fence post hole. If you don’t see concrete in the walk-out, take a common shovel and dig down a couple of inches next to the broken post location to see in the event you hit concrete. Most fence posts are placed in concrete and for the most part a conventional post hole is around eight (8″) to twelve (12″) inches across a great number are about twenty-four (24″) inches deep.
You can find different ways of thinking in regards to removing a current post. A lot of people choose to smash and grab technique that is certainly simply utilizing a hammer and chisel or pry bar to break the concrete into small pieces and pull them outside the existing hole individually. The process really does work but quite a bit of work and it may take between one (1) and (2) hours of to extract the concrete within the hole. It really is fine in case you have 1 post to interchange but if there can be multiple, the task involved is incredibly tedious and tiring for you be more effective ways.
The way I favor would be to require a long, skinny bladed shovel and seek out the dirt merely to the side of your concrete exposing the medial side from the concrete block. Make certain you pile the dirt at the hole as being the dirt you remove can be employed to re-pack the outlet when the post and concrete block is taken off within the ground. Through the aspect the concrete, dig out about six (6″) to eight (8″) inches and down twenty-four (24″) inches. Provide for that pocket as wide being the concrete block. If your piece or stump from your existing post continues to it is in place, to generate videos and get started moving the concrete block between with the new pocket space you created. Once it really is loose, always be able to use your shovel or pry bar being a lever and lift the concrete block belonging to the hole. Be careful and make certain you lift with each of your legs as being the concrete block can weigh nearly eighty (80) pounds. If for example the existing post or post stump stop being linked to the concrete, try to be able to use a pry bar as well as your shovel to safely move the prevailing concrete block backward and forward in a similar manner loosening it looking at the original placement. Once, the block is movable, operate the same process as pointed out above but please be careful to work with proper lifting techniques when taking out the concrete. A doctors visit just isn’t prescribed on this project.
Should the block is taken off, make use of the dirt you faraway from the excavation to submit the six (6″) to eight (8″) inches you originally dug out. Don’t forget to pack the dirt solidly simply because it will offer the lateral support to the new post several weeks set up. The concrete you select when you set the revolutionary post will give a lot of support apart from attaching the prevailing fence structure nevertheless the better you pack the dirt, better the consequence. You will be still the standard hole approximately twenty-four (24″) inches deep and approximately eight (8″) to twelve (12″) inches wide.
At this point, you must bring your clam digger or post hole digger or if you don’t possess one, use your shovel and find approximately two (2″) inches at the base from the hole. Adding loose gravel in the two (2″) inches for drainage to prevent water away from the bottom for the post. If you don’t have or would not invest in a bag of gravel as soon as you purchased your replacement post and concrete, don’t be concerned. The concrete has gravel inside it and will work however the gravel does make your drainage more efficient. Once you have the beds base in place, it is time to install the replacement post.
Grab your replacement post and center it on the hole. When you’ve got a helper, keep these things have the post make certain not wearing running shoes lines up correctly along with the fence along with the old post a charge card removed. After you have it inside correct position, open an eighty (80) pound bag of Quickrete concrete and pour it dry towards the hole. Verify that you are wearing eye protection and to cover your mouth area and that means you really do not inhale the concrete dust that typically spews away from the hole whilst you pour inside the mixture. Pour all of the contents into the hole. Grab a garden hose or simply a bucket of water you should pouring water into the hole and assure to pour about the new post inside of a circular pattern to successfully obtain the whole top layer belonging to the concrete wet. This type of water will rapidly bubble the way it starts seeping in the bottom. Will continue to add water until it pools a little. It is going to absorb through the mix. At this moment, bring your pry bar or even a part of rebar and even a sturdy stick you should poking the concrete mixture to help have the water to circulate down to the lower not to mention dispose of air bubbles that form. It is OK generally if the water pools a lttle bit in addition to produce the mixture too wet given it requires longer to create.
Now bring your level and be sure of the fact that post remains in the upright vertical position. It happens to be helpful in the event you check into multiple sides and make certain the bubble on the level is with the middle and relating to the marks. When the post is level, use bits of wood to develop a stand of sorts below to maintain the post from moving while the concrete sets up overnight. The concrete begins setting and dependent upon the climate really should be ready next week to re-hang a fence pieces. If the post moves, wiggle it on the vertical position and be able to making use of your stick or pry bar, move the concrete mix around therefore it touches the post on all sides in your yard without a gaps. If gaps form, you may need to put in a amount of additional water to make the mixture more liquid. Any pooled water might be made available to the concrete and surrounding dirt in addition to evaporate being the concrete sets.
The next day, just be ready to re-affix fences towards post therefore it needs to be good as new. Prior to attach the previous fence pieces, you can the peak within the fence post compared to the other posts on your fence line. Depending on the rest of your fence, you might want to work with a hand or electric saw to reduce the new post to fit the other one posts on your own fence. In case the post need not be cut, then you can certainly attach the actual fence pieces towards the new post. Don’t forget to use screws if you attach the fence it back into the new post to assure a stable connection than nails which sometimes remove in windy or rainwater conditions in time causing integrity issues.
The actual project is known as a moderate or medium difficulty project and needs to take approximately sixty (60) to ninety (90) minutes to carry out.